View 74FST3861-D_856797.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

74FST3861 10-Bit Bus Switch
The ON Semiconductor 74FST3861 is a 10-bit, high performance bus switch. The device is CMOS TTL compatible when operating between 4 and 5.5 Volts. The device exhibits extremely low RON and adds nearly zero propagation delay. The device adds no noise or ground bounce to the system. * RON t 4 W Typical * Less Than 0.25 ns-Max Delay Through Switch * Nearly Zero Standby Current * No Circuit Bounce * Control Inputs are TTL/CMOS Compatible * Pin-For-Pin Compatible With QS3861, FST3861, CBT3861 * All Popular Packages: SOIC-24, TSSOP-24, QSOP-24
http://onsemi.com
MARKING DIAGRAMS
24 24 1 SO-24 DW SUFFIX CASE 751E 1 FST3861 AWLYWW
NC A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 GND
1 2 3 4 5 6 7 8 9 10 11 12
24 23 22 21 20 19 18 17 16 15 14 13
VCC OE B1 B2 B3 B4 B5 B6 B7 B8 B9 B10
TRUTH TABLE
Input OE L H Operation A Port = B Port Disconnect 24 1 TSSOP-24 DT SUFFIX CASE 948H 1 24 FST 3861 ALYW
NOTE: H = HIGH Voltage Level L = LOW Voltage Level 24
24 1 QSOP-24 QS SUFFIX CASE 492B A L, WL Y, YY W, WW = = = = FST3861 AWLYYWW 1
SO24-7/SO24-8/SO24-9 Figure 1. 24-Lead Pinout
PIN NAMES
Pin OE NC A1 to A10 B1 to B10 Description Bus Switch Enables No Connect Bus A Bus B
Assembly Location Wafer Lot Year Work Week
ORDERING INFORMATION
Device 74FST3861DW 74FST3861DWR2 74FST3861DT 74FST3861DTR2 74FST3861QS 74FST3861QSR Package SO-24 SO-24 TSSOP-24 TSSOP-24 QSOP-24 QSOP-24 Shipping 48 Units/Rail 2500 Units/Reel 96 Units/Rail 2500 Units/Reel 96 Units/Rail 2500 Units/Reel
(c) Semiconductor Components Industries, LLC, 2002
1
May, 2002 - Rev. 4
Publication Order Number: 74FST3861/D
74FST3861
A1 2 22 B1
A10
11
13
B10
OE
23
Figure 2. Logic Diagram
http://onsemi.com
2
74FST3861
MAXIMUM RATINGS
Symbol VCC VI VO IIK IOK IO ICC IGND TSTG TL TJ qJA DC Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Sink Current DC Supply Current per Supply Pin DC Ground Current per Ground Pin Storage Temperature Range Lead Temperature, 1 mm from Case for 10 Seconds Junction Temperature Under Bias Thermal Resistance SOIC TSSOP QSOP VI t GND VO t GND Parameter Value *0.5 to )7.0 *0.5 to )7.0 *0.5 to )7.0 *50 *50 128 $100 $100 *65 to )150 260 )150 125 170 200 Level 1 Oxygen Index: 28 to 34 Human Body Model (Note 1) Machine Model (Note 2) Charged Device Model (Note 3) Above VCC and Below GND at 85C (Note 4) UL 94 V-0 @ 0.125 in u2000 u200 N/A $500 V Unit V V V mA mA mA mA mA C C C C/W
MSL FR VESD
Moisture Sensitivity Flammability Rating ESD Withstand Voltage
ILATCH-UP
Latch-Up Performance
mA
Maximum Ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute maximum-rated conditions is not implied. Functional operation should be restricted to the Recommended Operating Conditions. 1. Tested to EIA/JESD22-A114-A. 2. Tested to EIA/JESD22-A115-A. 3. Tested to JESD22-C101-A. 4. Tested to EIA/JESD78.
RECOMMENDED OPERATING CONDITIONS
Symbol VCC VI VO TA Dt/DV Supply Voltage Input Voltage Output Voltage Operating Free-Air Temperature Input Transition Rise or Fall Rate Switch I/O Switch Control Input VCC = 5.0 V $ 0.5 V Parameter Operating, Data Retention Only (Note 5) (HIGH or LOW State) Min 4.0 0 0 *40 0 Max 5.5 5.5 5.5 )85 DC 5 Unit V V V C ns/V
5. Unused control inputs may not be left open. All control inputs must be tied to a high or low logic input voltage level.
http://onsemi.com
3
74FST3861
DC ELECTRICAL CHARACTERISTICS
VCC (V) 4.5 4.0 to 5.5 4.0 to 5.5 0 v VIN v 5.5 V 0 v A, B v VCC VIN = 0 V, IIN = 64 mA VIN = 0 V, IIN = 30 mA VIN = 2.4 V, IIN = 15 mA VIN = 2.4 V, IIN = 15 mA ICC DICC Quiescent Supply Current Increase In ICC per Input VIN = VCC or GND, IOUT = 0 One input at 3.4 V, Other inputs at VCC or GND 5.5 5.5 4.5 4.5 4.5 4.0 5.5 5.5 4 4 8 11 2.0 0.8 $1.0 $1.0 7 7 15 20 3 2.5 mA mA TA = *405C to )855C Min Typ* Max *1.2 Unit V V V mA mA W
Symbol VIK VIH VIL II IOZ RON
Parameter Clamp Diode Resistance High-Level Input Voltage Low-Level Input Voltage Input Leakage Current OFF-STATE Leakage Current Switch On Resistance (Note 6) IIN = *18mA
Conditions
*Typical values are at VCC = 5.0 V and TA = 25C. 6. Measured by the voltage drop between A and B pins at the indicated current through the switch. On resistance is determined by the lower of the voltages on the two (A or B) pins.
AC ELECTRICAL CHARACTERISTICS
TA = *405C to )855C CL = 50 pF, RU = RD = 500 W VCC = 4.5-5.5 V Symbol tPHL, tPLH tPZH, tPZL tPHZ, tPLZ Parameter Prop Delay Bus to Bus (Note 7) Output Enable Time, IOE to Bus A, B Output Disable Time, IOE to Bus A, B Conditions VI = OPEN VI = OPEN for tPZH VI = OPEN for tPHZ 1.0 1.0 Min Max 0.25 5.1 5.5 VCC = 4.0 V Min Max 0.25 5.6 5.5 Unit ns ns ns
7. This parameter is guaranteed by design but is not tested. The bus switch contributes no propagation delay other than the RC delay of the typical On resistance of the switch and the 50 pF load capacitance, when driven by an ideal voltage source (zero output impedance).
CAPACITANCE (Note 8)
Symbol CIN CI/O Parameter Control Pin Input Capacitance A/B Port Input/Output Capacitance VCC = 5.0 V VCC, OE = 5.0 V Conditions Typ 3 5 Max Unit pF pF
8. TA = )25C, f = 1 MHz, Capacitance is characterized but not tested.
http://onsemi.com
4
74FST3861
AC Loading and Waveforms
VI FROM OUTPUT UNDER TEST CL * 500 W
500 W
NOTES: 1. Input driven by 50 W source terminated in 50 W. 2. CL includes load and stray capacitance. *CL = 50 pF
Figure 3. AC Test Circuit
tf = 2.5 nS 90 % SWITCH INPUT 1.5 V 10 % tPLH 90 % 1.5 V
tf = 2.5 nS 3.0 V
10 % tPLH
GND VOH
1.5 V OUTPUT
1.5 V VOL
Figure 4. Propagation Delays
tf = 2.5 nS tf = 2.5 nS ENABLE INPUT 90 % 1.5 V 10 % tPZL OUTPUT 10 % 90 % 1.5 V GND tPZL 3.0 V
1.5 V
VOL + 0.3 V VOL tPHZL VOH
tPZH
1.5 V OUTPUT
VOH - 0.3 V
Figure 5. Enable/Disable Delays
http://onsemi.com
5
74FST3861
PACKAGE DIMENSIONS
-A-
24 13
SO-24 D SUFFIX CASE 751E-04 ISSUE E
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN EXCESS OF D DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A B C D F G J K M P R MILLIMETERS MIN MAX 15.25 15.54 7.40 7.60 2.35 2.65 0.35 0.49 0.41 0.90 1.27 BSC 0.23 0.32 0.13 0.29 0_ 8_ 10.05 10.55 0.25 0.75 INCHES MIN MAX 0.601 0.612 0.292 0.299 0.093 0.104 0.014 0.019 0.016 0.035 0.050 BSC 0.009 0.013 0.005 0.011 0_ 8_ 0.395 0.415 0.010 0.029
-B-
12X
P 0.010 (0.25)
M
B
M
1
12
24X
D 0.010 (0.25)
M
J TA
S
B
S
F R C -T-
SEATING PLANE X 45 _
M
22X
G
K
http://onsemi.com
6
74FST3861
PACKAGE DIMENSIONS
TSSOP-24 DT SUFFIX CASE 948H-01 ISSUE A
24X K REF NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 7.70 7.90 4.30 4.50 --1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.27 0.37 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.303 0.311 0.169 0.177 --0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.011 0.015 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_
0.10 (0.004) 0.15 (0.006) T U
S
M
TU
S
V
S
2X
L/2
24
13
L
PIN 1 IDENT. 1 12
B -U-
0.15 (0.006) T U
S
A -V-
C 0.10 (0.004) -T- SEATING
PLANE
D
G
H
N K K1 J1
0.25 (0.010) M -W-
SECTION N-N J
CCC EE CCC EE
N F DETAIL E DETAIL E
http://onsemi.com
7
74FST3861
PACKAGE DIMENSIONS
QSOP-24 QS SUFFIX CASE 492B-01 ISSUE O
-A- R U -B-
Q H x 45_
MOLD PIN MARK
RAD. 0.013 X 0.005 DP. MAX RAD. 0.005-0.010 TYP
L
P 0.25 (0.010)
M
G T
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. THE BOTTOM PACKAGE SHALL BE BIGGER THAN THE TOP PACKAGE BY 4 MILS (NOTE: LEAD SIDE ONLY). BOTTOM PACKAGE DIMENSION SHALL FOLLOW THE DIMENSION STATED IN THIS DRAWING. 4. PLASTIC DIMENSIONS DOES NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 6 MILS PER SIDE. 5. BOTTOM EJECTOR PIN WILL INCLUDE THE COUNTRY OF ORIGIN (COO) AND MOLD CAVITY I.D. INCHES DIM MAX MIN A 0.337 0.344 B 0.150 0.157 C 0.061 0.068 D 0.008 0.012 F 0.016 0.035 G 0.025 BSC H 0.008 0.018 J 0.0098 0.0075 K 0.004 0.010 L 0.230 0.244 M 0_ 8_ N 0_ 7_ P 0.027 0.037 Q 0.035 DIA R 0.035 0.045 U 0.035 0.045 V 0_ 8_ MILLIMETERS MAX MIN 8.56 8.74 3.81 3.99 1.55 1.73 0.20 0.31 0.41 0.89 0.64 BSC 0.20 0.46 0.249 0.191 0.10 0.25 5.84 6.20 0_ 8_ 0_ 7_ 0.69 0.94 0.89 DIA 0.89 1.14 0.89 1.14 0_ 8_
DETAIL E
V N 8 PL K -T- C
24 PL
J M
D
M
SEATING PLANE
F DETAIL E
0.25 (0.010)
TB
S
A
S
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative.
http://onsemi.com
8
74FST3861/D
This datasheet has been download from: www..com Datasheets for electronics components.

▲Up To Search▲

Price & Availability of 74FST3861-D

	To Download 74FST3861-D Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .